VFC MP5 to Compact Drum - PLUG and PLAY
Choose options
This adapter lets you run your VFC MP5 on HPA.
Requires a donor gas router from a VFC MP5 magazine. Valve and feed lips are provided.
To fit the gas router, remove the 4 screws from the top of the adapter, lift the feed lips, place the gas router underneath, and refit the feed lips. Be careful not to over tighten the screws
You can run the adapter at 120-150PSI.
We utilise a very high flow valve. This has allowed us to build a far more reliable adapter that is capable of high FPS and sustained full auto.
US Style HPA Fitting as Standard (most common fitting across industry - compatible with all AIRTAC HPA equipment)
*Drum mag not included. You can purchase drum here.
DO NOT EXCEED 150PSI WITH ANY AIRSOFT HPA ADAPTER.
ALWAYS USE AIR REGULATED BY A SECONDARY REGULATOR (EG AT200, WOLVERINE STORM, POLARSTAR MRS).
CHECK YOUR PSI BEFORE CONNECTING AIR TO A HPA ADAPTER.
NEVER CONNECT OUR EQUIPMENT TO PAINTBALL AIR TANKS OR CO2 TANKS.
NEVER CONNECT OUR EQUIPMENT TO A TIPPMAN STYLE HPA LINE
AIRTAC Adapters
Each of our adapters is designed to be low profile while reaching field limit FPS. We design and manufacture all of our products to the highest standard, and do not charge extra for ‘premium’ features. Where applicable this adapter features:- Lifetime Warranty (Our adapters have to be built to last)
- Injection moulded or CNC magwell that is impervious to BB strikes at point blank skirmish FPS.
- CNC or Injection moulded Feed Tubes and Magazine Catches for lifelong durability.
- Tuneability/compatability via integrated shim systems. Our adapters are designed to cope with 'airsoft tolerances'
- Gas Routers injection moulded from NBR, 1:1 with the factory gas router.
- Seal Test
- Firing test, for feed and recoil (we have over 100 guns on site for testing)
Plug and Play
This adapter is ready to go out of the box. Valve, feed lips, and gas router are already fitted to the adapter. You do not need to use any donor parts.No assembly is required.
Compact MP5
Drum Adapter Info
- Compatible with TM MP5/ TM SCORPION Drum Magazines Available here
Also compatible with Jing Gong VZ61 drums, though these can be hard to source - 100+ BBs from a full wind
- Drum adapters include 2 25mm pins for installation of adapter onto drum
- Disassembly of drum and installation onto adapter can be seen below (you can skip the middle section of video as this is specific to TM MP7)
Key Information
- We use a US Foster Fitting as standard. This is the most common airsoft HPA fitting. EU fittings can be purchased separately.
- Some of our HPA adapters have a smaller internal volume than gas magazines. Because of this, you will need to use a PSI of 90–150.
-
If you need higher FPS, you can:
- Fit a tighter barrel
- Use a longer barrel
- Use heavier BBs
- Fit an improved hop bucking
- If your replica has an NPAS fitted, we advise opening it fully.
- Do not exceed 150 PSI. Many airsoft guns will not see an increase in FPS past this, as the hammer may struggle to depress the valve correctly.
- Insert the HPA adapter with your bolt / slide locked back to minimise pressure against the nozzle loading arm.
Run different mags with your adapter!
This adapter is also compatible with the following modular magwells. Its a great way to change up your playstyle and aesthetic!| Magazine Type | Compatibility | Magwell |
|---|---|---|
| M4 | ✅ | View |
| M4 (Angled) | ❌ | View |
| MP5 | ✅ | View |
| Shotshell (Pistol Style) | ✅ | View |
| Shotshell (Rifle Style) | ❌ | View |
| Remote Feed | ✅ | View |
| Compact Drum | ✅ | View |
DO NOT EXCEED 150PSI WITH ANY AIRSOFT HPA ADAPTER.
ALWAYS USE AIR REGULATED BY A SECONDARY REGULATOR (EG AT200, WOLVERINE STORM, POLARSTAR MRS).
CHECK YOUR PSI BEFORE CONNECTING AIR TO A HPA ADAPTER.
NEVER CONNECT OUR EQUIPMENT TO PAINTBALL AIR TANKS OR CO2 TANKS.
NEVER CONNECT OUR EQUIPMENT TO A TIPPMAN STYLE HPA LINE